- #Wiring a ceiling fan with light and 4 wires from ceiling how to#
- #Wiring a ceiling fan with light and 4 wires from ceiling portable#
#Wiring a ceiling fan with light and 4 wires from ceiling portable#
If you’ve done your job correctly, the fan and the light should come on when you turn the wall switch (or portable remote) to the on position. Once the connections are made, you can turn the power back on and test the fan to make sure everything is working. Step 5: Test Ceiling Fan & light Operation
#Wiring a ceiling fan with light and 4 wires from ceiling how to#
If you have questions – like – what ceiling fan bracket should I use? Please see our How To Install ceiling bracket content below. Step 4: Install Ceiling Fan With Light Kitįollow the Manufacturer’s specific instructions to install a light kit onto the ceiling fan, and secure the ceiling fan assembly to the ceiling mount bracket. Of course with the above method, your ceiling fan must have two “exposed” chains for operating the fan and the light kit separately. If You plan to provide power to the Fan & Light and Switch simultaneously (not using the pull chain for the fan separately) refer to this diagram:įinally: If you plan to wire your ceiling fan and light so they BOTH operate from pull chains – refer to this diagram: If however, you are planning to wire the fan motor and light independently or are using a fan fixture that does not include pull switches, you may need to look up a ceiling fan wiring diagram that is specific to the way you’re approaching the project. This method involves a single-power switch that will supply power to both the fan motor and the light itself, both of which have independent pull switches located on the fixture. It should be noted that the instructions above are for the simplest and most common method of wiring a ceiling fan. You can always cut off any extra exposed wire before you put the connector on if necessary. Make sure to get a firm connection at each joint by twisting the wires together before finishing the connection with twist-on wire nuts.Īlso, be sure to strip enough insulation off of each wire to give yourself plenty of room to make solid contact. The second one will be used to connect the two white neutral wires, while the third will join the ground wires. The first connector will join the black power supply wire from the electrical box to the black and blue wires from the fan. For this, you’ll need three twist-on wire connectors. Once you have found and identified all of the wires on your fan and in your electrical box, you can get to work on connecting them. The wiring diagram above is for “Typical” wiring (Light is Switched & the Fan is powered by a pull chain) Step 3: Connect the WiresĬeiling fan connection – Light wired to Light Switch Fan On/Off with Pull Chain If you’re wiring a ceiling fan with light with one switch, though, this additional wire won’t be needed. If you have a double switching setup, you should find an additional wire, usually red, in your ceiling box. As with the wires in the fan itself, the black wire is hot, and the white wire is neutral.Īlthough this usually won’t apply, there will be a slight difference if you have independent switches for the fan and the light, rather than running both from the same switch. You should find one black wire and one white wire in the box, as well as a bare copper ground wire. In addition to the wires on the fan itself, you’ll need to identify the wires in your ceiling box. While you should read the instructions on your new fan carefully to be sure, the convention is that the black wire is a power supply for the fan, the blue wire is a power supply for the light, the white wire is neutral, and the green wire is a ground. Typically, you’ll see black, white, blue, and green wires inside a ceiling fan. The wires inside of a ceiling fan are relatively simple, but you have to know what each one is to connect them correctly. The voltage tester should be applied to the black wire inside your fan’s electrical box, as this is usually the hot wire from the power supply. Remove any possibility of electrical shock. Even if the breaker switches are clearly labeled, it’s also a good idea to use a non-contact voltage tester to confirm that the power is off before proceeding, as it’s always possible that the breakers are mislabeled. Wiring a Ceiling Fan and Light – Getting Started: Here are the 5 steps to install a Ceiling Fan and Light: Step 1: Turn Off Power at the Breakerīefore you can start wiring your new ceiling fan, you’ll need to turn off the power to its circuit by flipping the correct breaker in your home’s electrical panel. Once you understand the ceiling fan wiring colors, and even if you’ve never attempted to wire a ceiling fan, the steps involved are very simple and accessible to even the most casual DIY handy person. Parts of a Toilet – Toilet Tank Diagram.